MATLAB XPC TARGET 4 - API GUIDE Guide de l'utilisateur Page 99
- Page / 372
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
4
Embedded Option
The xPC Target Embedded Option allows you to boot the target PC from a device other than a
3.5 inch disk drive, such as a hard disk or flash memory. It also allows you to deploy stand-alone
applications on the target PC independent of the host PC. This chapter includes the following
sections:
Introduction (p. 4-2) Learn about the different types of embedded target
applications you can create using the xPC Target
Embedded Option
xPC Target Embedded Option Modes
(p. 4-3)
Learn about the xPC Target Embedded Option modes
Embedded Option Setup (p. 4-9) Configure xPC Target to generate embedded target
applications and create a DOS system boot disk
DOSLoader Target Setup (p. 4-12) Create a target application that boots from a device other
than a 3.5 inch disk drive
Stand-Alone Target Setup (p. 4-17) Create a target application that runs on the target PC
disconnected from the host PC and, optionally, boots from
a device other than a 3.5 inch disk drive
- User’s Guide 1
- How to Contact The MathWorks: 2
- Embedded Option 6
- Troubleshooting 10
- Function Reference 11
- Contents 12
- Target and Scope Objects 13
- 1 Target and Scope Objects 14
- Scope Objects 15
- Targets and Scopes in the 19
- MATLAB Interface 19
- Working with Target Objects 20
- Deleting Target Objects 21
- 2 Alternatively, you can type 22
- Working with Scope Objects 25
- 2 Alternatively, type 26
- Signals and Parameters 37
- 3 Signals and Parameters 38
- Monitoring Signals 39
- Signal Tracing 47
- Add Target Scope 49
- Add to Scopes 53
- Software Triggering Scopes 57
- Scope of Type Host 69
- Scope of Type Target 69
- Interrupted) or finishes 71
- Signal Logging 75
- Signal logging 75
- Enter key 81
- Parameter Tuning with MATLAB 83
- Simulation menu, click 87
- Connect to target 87
- Configure button 93
- Add to table 93
- Update Parameter button 95
- 4 Embedded Option 100
- 9 Boot the target PC 103
- *.rtb file 105
- Embedded Option Setup 107
- Creating a DOS System Disk 109
- Create BootDisk 111
- DOSLoader Target Setup 111
- Reset button on your target 113
- Stand-Alone Target Setup 115
- Software Environment 123
- 1 In the MATLAB window, type 124
- Explorer 125
- Command-Line Interface 128
- In the MATLAB window, type 129
- Using the Target PC 131
- C. In this case 132
- Target PC 133
- System: S0 has value 5.1851 134
- Working with Target PC 139
- Files and File Systems 139
- Introduction 140
- FTP and File System Objects 142
- Using xpctarget.ftp Objects 143
- Using xpctarget.fs Objects 147
- Graphical User Interfaces 155
- 8 Graphical User Interfaces 156
- Host PC Target PC 157
- To xPC Target Block 159
- Block Parameters 161
- Signal Properties 165
- Documentation tab 165
- Interface 169
- Web Browser Interface 170
- Ctrl+C by 172
- Ctrl+C is not used to 172
- Using the Main Pane 174
- Main pane 175
- Changing WWW Properties 177
- -1 or Inf 178
- 1, enter 180
- Interrupts Versus Polling 181
- 10 Interrupts Versus Polling 182
- Polling Mode 183
- Target Application 189
- Polling Mode Performance 193
- 11 xPC Target and Fortran 196
- Prerequisites 197
- Compiling Fortran Files 201
- Parameters 205
- 12 Troubleshooting 210
- Is the Target PC Halted? 211
- Create Bootdisk 219
- Advanced Troubleshooting 223
- Can Library parameter in 225
- PCI Slot parameter of 225
- Target PC Command-Line 235
- Interface Reference 235
- Target PC Commands 236
- Target Object Methods 237
- Scope Object Methods 239
- or move mouse 243
- 14 Function Reference 246
- Target Objects 247
- Functions — Categorical List 251
- 14addscope 253
- Syntax MATLAB command line 253
- Arguments 253
- MATLAB command line 258
- Purpose Remove target object 260
- function 262
- 14fc422mexcalcbits 265
- 14get (scope object) 272
- AutoRestart check box to 273
- Number of samples, then 273
- 14get (target object) 281
- 14getxpcenv 297
- Syntax MATLAB Command Line 297
- RAM size 298
- Target boot mode 304
- Purpose Reboot target PC 312
- 14set (scope object) 320
- Description 320
- 14set (target object) 329
- Simulation 331
- 14setxpcenv 334
- Interface” on page 5-6 342
- Target PC command line 345
- 14updatexpcenv 352
- 14xpcexplr 355
- 14xpctarget.fs 356
- 14xpctarget.ftp 358
- 14xpctarget.xpc 360
- MATLAB Command Line 364
- 14xpcwwwenable 365
© 2020, manymanuals.fr. Tous droits réservés | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels